1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test . Integrated Circuit. Transistor Transistor Logic (TTL). 4−Line−to−16−Line Decoder /Demultiplexer. 24−Lead DIP Type Package. Description: The NTE is a. datasheet, circuit, data sheet: NSC – 4-Line to Line Decoders/Demultiplexers,alldatasheet, datasheet, Datasheet search site for.

Author: Dur Tojam
Country: Anguilla
Language: English (Spanish)
Genre: Software
Published (Last): 18 January 2010
Pages: 118
PDF File Size: 9.23 Mb
ePub File Size: 20.90 Mb
ISBN: 137-4-76450-966-6
Downloads: 18715
Price: Free* [*Free Regsitration Required]
Uploader: Vizahn

Repeat the above 741544 i once again. Working of the monostable multivibrater already discussed. Circuit diagram of the DTMF encoder. And that’s what is going on with the This contains one telephone line and a control unit. By this transistor is forward biased and the output is obtained at the emitter of the transistor.

These tones are identified as ‘A’, ‘B’, ‘C’, ‘D’. When the output of D flip-flop goes low the base voltage drops below 0. When either strobe input is high, all outputs are high.

4 Line to 16 Line Demultiplexer / Decoder

It inhibits the detection of Hz. The dialed number of the device is displayed on seven segment display.

The row and column frequency of this IC is as on the fig. On getting the ringing signal this circuit connects the master unit to the telephone line.

The connecters are provided to all the relay switches so that the devices are connected easily. This check is performed by an external RC time constant driven by ESt. Here common anode seven segment display is used.


A seven segment display has seven LEDs connected in a sequence to give a regular shape and a LED to display the dot for decimal point. After a period of 5 seconds the output of the IC 6 goes low and puts the tri state buffer in the high impedance dattasheet. This circuit is directly connected to the telephone line. When control signal is at high state, the outputs are nothing but the data present at its input terminals.

Post as a guest Name. IC is a conventional D-flip-flop IC.

National Semiconductor

Provision is made for connection of a feedback resistor to the op-amp output GS for gain adjustment. These two tones are taken from a row frequency and a column frequency. Each of the low and high frequency groups comprise four frequencies from the various keys present on the telephone keypad; two different frequencies, one from the high frequency group and another from the low frequency group are used to produce a DTMF signal to represent the pressed key.

Beep tone generator unit produces a beep tone of audible frequency. By pressing any key in the keyboard corresponding DTMF signal is available in its output pin at pin no.

By using this IC we can construct two types of multivibrater, monostable and astable. These demultiplexer are ideally suited for implementing high-performance memory decoders.

(PDF) 74154 Datasheet download

It makes accurate switching, any false switching of device are not done. This device status feedback unit uses daasheet dual input AND gate, the output of the flip flop and the tri state buffer are to as the input.


Its filter section uses switched capacitor technology for both the high and low group filters and for dial tone rejection. Sign up using Facebook. Email Required, but never shown. The filter also incorporates notches at and Hz, providing excellent dial tone rejection.

Is the hardware implementation circuit different than the ix explained in theory? So now the device code of the respective device is again pressed whose status is to be altered. When this key is pressed the output of the line decoder goes low.

Datasheet(PDF) – National Semiconductor (TI)

The internal clock circuit is completed with the addition of a standard 3. After changing the present status of datasneet device confirm the operation you did, here comes the unit which gives the feedback tone after switching ON any device.

It is nothing but remote telephone set which is present in the remote place.

This is a control system through which you can control your appliances. These flip-flops are used to latch the data that present at its input terminal click here to download datasheet. By using this project we can construct the personally branched telephone exchange.

Here we use the transistors to energize the relay coil. The monostable multivibrater produces a single pulse when a triggering pulse is applied to its triggering input. Yes here is the solution.