ASTM F788 PDF

Designation: F /F M â 07 Standard Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series1 This. ASTM F/FM: Standard Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series. Designation: F /F M – 05 Standard Speci?cation for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series1 This.

Author: Yozshuzshura Arasar
Country: Singapore
Language: English (Spanish)
Genre: Politics
Published (Last): 11 May 2014
Pages: 397
PDF File Size: 14.39 Mb
ePub File Size: 20.38 Mb
ISBN: 334-9-61210-780-8
Downloads: 90289
Price: Free* [*Free Regsitration Required]
Uploader: Faeshakar

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any asmt mentionedin this standard.

Shear bursts may also occur on the sides of hex-head products. The values stated in each system are not exact equivalents, therefore, each system must be used independently of the other.

Historical Version s – view previous versions of standard. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Appendix 2 astm d F Terminology for F16 Mechanical Fasteners.

Users of this standard are expressly advised that determination of the aztm of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn.

Register for a trial account.

Combining values from the two systems may result in nonconformance with the speci? Copyright Compu-tecture, Inc. Enter your personal account email address to request a password reset: This specification establishes allowable limits for the various types of surface discontinuities that may occur during the manufacture and processing of bolts, screws, and studs, including heat-treated machine screws, tapping screws, and sems.

  FRANK GAMBALE SPEED PICKING PDF

A number in parentheses indicates the year of last reapproval. A superscript epsilon e indicates an editorial change since the last revision or reapproval. Acceptance shallbe based on the requirements of S1. They arenot planished during forging.

Typical tool marks are shown in Fig. The section shall be etched for microscopic examina-tion in accordance with Test Method E Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend.

Current edition approved Oct. Types of surface discontinuities are: Combiningvalues from the two systems may result in nonconformancewith the specification. Typical voids are shown in Fig.

The valuesstated in each system are not exact equivalents, therefore, eachsystem must be used independently of the other. Visual inspection can include the use of devices that provide up to, and including, power magni?

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. The section shall be etched for microscopic examination in accordance with Test Method E Link to Active This link will always route t788 the current Active version of the standard.

Types of Surface Discontinuities see TerminologyF for definitions not provided 4. NOTE 1—Forging cracks within the limits of this speci? There are no ISO astmm for surface discontinuities on any inch-series products. Bolt astm a pdf – astm a pdf Bolt astm a pdf Bolt astm a pdf Limits are specified in5. Shear bursts occur most frequently at the periphery of productshaving flanged or circular heads. This standard has been approved for use by agencies of the Department of Defense.

  FREISTELLUNGSAUFTRAG BANK OF SCOTLAND PDF

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

ASTM-F/FM-, 0 –

The values stated in each system are not exact equivalents, therefore, each system must be used independently of the other. This standard has been approved for use by agencies of the Department of Defense. For metric series products, D and Dc are in millimetres; for inch-series products, D and Dc are in inches. ASTM E Land Use and Development. Combining values from the two systems may result in non-conformance with the standard.

Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters.

ASTM F788.pdf

Limits arespecified in 5. There were no books found for the applied search filters.

Supplementary Requirements shall in no way negate any requirement of the speci? This abstract is a brief summary of the referenced standard. Xstm are specified in 5.

Print 1 2 3 4 5 page sstarting from page current page.